Deluxe Series Multi-Purpose

Deluxe Series Multi-Purpose

Natural Look Finish, Zero Gloss

Water Base Sealer for Dry Cast Concrete Pavers, Masonry & Natural Stones

Description

Polybind DELUXE NATURAL LOOK FINISH, zero gloss, water-based sealer for natural stones is made from fluorochemical polymers. This multi-purpose sealer penetrates deep into the natural stones, concrete pavers, walls, masonry thus reducing the oil and dirt penetration, as well as protecting them from the corrosion of de-icing salt.

Features

  • Non film forming
  • Works at above 32°F (0°C)
  • Water repellent, applicable on damp surfaces
  • Zero VOC
  • Water base sealer
  • 10 year warranty

Application & Installation

APPLICATION INSTRUCTIONS FOR PAVERS & NATURAL STONES:

  1. ALWAYS TEST the product on a small hidden area of approximately 4 sq. ft. to ensure the results will meet your expectations.
  2. Remove all contaminated jointing material and replace with Polybind Polymeric Sand. Follow the instructions on the back of the bags for proper polymeric sand installation.
  3. Wait at least 48 hours at a minimum temperature of 60°F (15°C) and no rain for the Polybind Polymeric Sand to properly harden.
  4. Clean off any stains with Polybind Clean products. Then use the Polybind Efflorescence Cleaner to remove the efflorescence trapped in the concrete paver or natural stone pores as well as thoroughly clean the surface for proper sealer adhesion.
  5. Apply 1 coat of Polybind Seal using a roller or sprayer on a dry surface.
  6. Let the sealer dry before using the sealed area.

APPLICATION INSTRUCTIONS FOR RETAINING WALLS & MASONRY:

    1. Use Polybind Clean Efflorescence Cleaner to remove any trapped efflorescence. It also thoroughly cleans the surface to ensure a proper sealer adhesion.
    2. Apply only 1 coat of Polybind Seal using a roller or sprayer.
    3. Let the sealer dry.

CLAY PAVERS
If using polymeric sand as jointing material, we recommend a test area. Some clay pavers are more porous and retain humidity, this might cause the polymers to react on the damp surface and cause a haze.

**PLEASE NOTE**

      • Wear protective gloves, Eye protection and respiratory protection.
      • Alliance Designer Products shall not be liable for any non-compliant use, unless the manufacturer, distributor, or seller knows that the supplied coating would be used in a noncompliant manner.

Coating Category: Low Solids Coatings. VOC Concentration Limits:

Coverage

  • Seals approx, 175 sq ft (16 sq. m.) per gallon

Packaging

Products Retail Size Per Box Per Pallet
Deluxe Series Natural Look 1 US gallon (3.78 L) 4 units 24 boxes
Deluxe Series Natural Look 5 US gallon (18.9 L) 0 units 48 pails

10 Years Limited Warranty

Before applying the product, the user/buyer must determine its suitability for intended use and user/buyer assumes all risks in that regard. It is a condition of the limited warranty that before using the product on the intended larger area, the user/buyer must first test the product on a small less observed area of approximately 4 sq. ft. (0.4 m2) to ensure results meet user/buyer’s expectations. In the event that no test is carried out, the limited warranty will only apply to 4 sq. ft. (0.4 m2). The container must at all times be stored at above 0°C / 32°F to receive the benefit under the limited warranty. Please note that this limited warranty applies only when the product purchased is used for the following purposes and on the following surfaces:

1. Residential Purposes (Homeowners or contractors using the product for single or multi-unit dwellings that are used exclusively for residential use) on:
• Horizontal surfaces
• Vertical surfaces (walls and masonry)

2. Commercial or Other Purposes (“Other Purposes” include mixed-use, institutional or non-residential purpose) on only:
• Vertical surfaces (walls and masonry)

ALLIANCE DESIGNER PRODUCTS INC. cannot guarantee results as it has no control over surface preparation and product application. However, for a period of 10 years from date of purchase, ALLIANCE DESIGNER PRODUCTS INC. agrees that, if the product is proven to be defective with respect to the specific purposes and surfaces stated above, and on the condition that it was applied pursuant to the method of application described in the applicable instructions, then ALLIANCE DESIGNER PRODUCTS INC. agrees to refund the purchase price. Proof of purchase is required for any claim. The parties agree that the refund of the purchase price as stated is the only obligation of the ALLIANCE DESIGNER PRODUCTS INC. In all events, ALLIANCE DESIGNER PRODUCTS INC. shall not be liable for any other damages or costs (including, without limitation, removal or reinstallation of pavers, bricks, stones, sand or mortar) whatsoever, direct or consequential. TO THE EXTENT PERMITTED BY LAW, ALLIANCE DESIGNER PRODUCTS INC. EXPRESSLY EXCLUDES ANY IMPLIED OR LEGAL WARRANTY OF QUALITY, MERCHANTABILITY OR FITNESS FOR PURPOSE.

1 YEAR LIMITED WARRANTY

Please note that when the product is used for COMMERCIAL or OTHER PURPOSES (as described above) on:
• Horizontal surfaces

The Limited Warranty is for 1 year from the date of purchase. Except that the duration of the warranty is limited to one (1) year, all the terms, conditions and exclusions mentioned above for a claim also apply.