Eurostone bond is the first polymeric sand specifically designed for natural stone pavers. It can be used in drainage base systems and overlay. It is perfect for stone roads, piazzas, driveways, pathways & stone apron driveways. This complete multi-purpose sand is available in four colors: Beige, Slate Grey, Ivory and Black.
For overlay applications: Make sure the paver stones are completely adhered to a permeable mortar bed base and cannot move.
For a drainage base: The installation of paver stones, must be interlocked with a minimum of 15 cm of 0-20 mm compacted stone and a maximum bedding sand course of 25 mm.
Make sure the sides and top surfaces of stones are dry before applying the EUROSTONE BOND polymeric sand. Sweep EUROSTONE BOND in between the stone joints.
Compact the sand in the joint with a vibrating plate and a hand tamper in restricted area. Sweep off all excess EUROSTONE BOND that is on the paver stone surface. Ensure that EUROSTONE BOND lies at least 3 mm below the top of the paver stones. Repeat twice the sweeping and compacting of the joint to ensure a good consolidation of the joint.
Using a leaf blower, remove any EUROSTONE BOND residue from the stone surfaces. Depending on the physical layout, it may be more appropriate to remove residue by using a vacuum unit.
Use a water gun connected to a hose to direct a shower stone (water gun setting: “shower” or equivalent) and direct water 1.2 m high so that it lands on a total area of 7 m2 of paver stone pavement for 10 to 15 seconds. Wait 3 to 4 minutes (no longer), then repeat this step twice, to remove residues from EUROSTONE BOND. However, stop watering if you notice water retention on the joints of pavers stones.
Repeat the directions of step 5 for all other paved areas that have not been showered with water. The water used in steps 5 & 6 will activate a bonding action as well as condense EUROSTONE BOND in the joints. It is important to water the EUROSTONE BOND a total of 3 times. Too little water will not properly activate the EUROSTONE BOND and will reduce the final performance.
IMPORTANT: If steps 5 & 6 are not done properly, a white haze may appear on stone paver surface after installation. This is due to excess Eurostone bond residue left on stone surfaces. This haze will dissipate over time. It can also be removed by using GATOR CLEAN efflorescence cleaner.
Do not apply if the paver surface is damp or wet. The damp or wet surface will cause EUROSTONE BOND to prematurely activate and will lead to the polymers sticking on the stone paver surface. Do not apply if the natural stone paver joints are damp or wet. This will prevent the EUROSTONE BOND from properly sliding into the joints and compromise the possibility of obtaining very densely packed joints, which is critical to the product’s performance. Do not use if rain is expected within 1 hour. Avoid excessive watering or flooding of natural stone paver surface. For all-natural stone paver surfaces, and particularly around in-ground pools, there must be a slope of 3mm per 30 cm away from the edge of the pool, or structures, to ensure optimal performance of the EUROSTONE BOND. For the pool coping units, it is mandatory to use mortar in the joints. For the rest of the natural stone paver installation around the pool, you can use EUROSTONE BOND. Do not sweep EUROSTONE BOND over asphalt. Install EUROSTONE BOND a minimum of 3mm below the natural stone paver surface or erosion may occur. The filled and cured EUROSTONE BOND joints should never be in direct contact with foot traffic or tires. The product must only be used as a recessed jointing material.
If using on clay pavers, make sure they are 100% dry. Clay pavers tend to hold moisture, which can prematurely activate the EUROSTONE BOND while the sand is being spread over the paver surface, leaving a residue (always apply on a test area before using the EUROSTONE BOND on clay pavers)
EUROSTONE BOND will not cause nor prevent moss, mold or mildew. Moss, mold and mildew are caused by certain on- site conditions, including excess moisture, shade, absence of ventilation, inadequate cleaning or maintenance, presence of soil or other organic debris left on the product.
Quantity required depends on the shape and size of paving area, the Natural stone pavers as well as the width of the joints. For Black Sand consider a 10% decrease in coverage.
|Narrow Joints||Wide Joints|
|Products||Retail Size||Units per Pallet|
|Eurostone Bond – Beige||22.7 kg||56|
|Eurostone Bond – Slate Grey||22.7 kg||56|
|Eurostone Bond – Ivory||22.7 kg||56|
|Eurostone Bond – Black Diamond||22.7 kg||56|
EUROSTONE BOND is recommended for a variety of uses, including pool sides, patios, foot paths, driveways, parking spaces, pavements, etc.
WITH A DRAINAGE BASE SYSTEM : The stone pavers have to be installed on a system composed of 2 layers. The upper layer can have a maximum of 2.5 cm of bedding sand. The lower layer must have a minimum of 15 cm of crushed stone compacted at 95% Proctor density.
WITH AN OVERLAY APPLICATION:(See diagrams below) you must have a minimum 1° top surface slope for proper water runoff for both systems.
This warranty is given by Alliance Designer Products inc. Please note that this limited warranty applies only when the product is used for residential purposes exclusively (home owners or contractors using the product for single or multi-unit dwellings that are exclusively for residential use). Alliance Designer Products inc. cannot guarantee results as it has no control over surface and sub-surface preparation and product application. However, for a period of 15 years from purchase, Alliance Designer Products inc. agrees that, if the product is proven to be defective, and on the condition that it was installed pursuant to the method of application of surface and sub-surface preparation described above, then the Alliance Designer Products inc. agrees to refund the purchase price. Proof of purchase is required for any claim.
Please note that when the product is used for other purposes (Mixed-use, commercial, institutional or other), the above terms apply except that the applicable period is reduced to 1 year from purchase.
The parties agree that refund of the purchase price as stated is the only obligation of alliance designer products inc. In all events, Alliance Designer Products inc. Shall not be liable for any other damages or costs (including removal or reinstallation of sand or pavers) whatsoever, direct or consequential. To the extent permitted by law, Alliance Designer Products inc. Exclude any implied warranty of quality, merchantability or fitness for purpose.
Alliance Designer Products Inc. excludes any responsibility whatsoever for the presence of moss, mold or mildew or similar facts that may occur on the product after its installation. The presence of moss, mold or mildew is caused by the particular on-site conditions, including excess humidity, shade, absence of ventilation, inadequate cleaning or maintenance, presence of soil or other organic debris left on the product after installation.